EC 610 C and EC 633 C

Quickly recoatable mineral levelling compounds for industrial floor renovation in combination with reactive resin coatings.

The renovation of old industrial floor coverings is always a special challenge. After decades of daily or intensive use, surfaces are massively worn and often even contaminated. In many cases, substrates in contact with the soil lack suitable sealing against rising damp.

These problems quickly become the downfall of the new coating. Therefore, it is important to minimise or, at best, exclude unforeseeable risks prior to floor renovation.

Usually, a refurbishment of such contaminated and severely damaged surfaces can only be solved by massive substance removal, e.g. by milling. The resulting roughened floor must be repaired, supplemented, levelled and finally smoothed with a levelling layer.

Alternatively, it is possible to renovate the surface with self-levelling epoxy resin fillers or mortars and thus, to create a durable floor covering. However, with high layer thicknesses and consumption quantities, this option is very costly or requires elaborate and time-consuming processing. Self-levelling mineral masses can circumvent this problem while being an excellent complement to reactive resins.

That’s convincing!

  • very fast-curing
  • low-shrinkage
  • self-levelling
  • recommended layer thickness 3 – 10 mm
  • high mechanical load-bearing capacity
  • low emission, suitable for recreation rooms
  • inexpensive and time-saving renovation alternative

Complex application with conventional mineral levelling compounds.

Mineral levelling compounds for industrial floor construction must be of high quality and suitable to absorb the subsequent coating. It is not uncommon for levelling compounds and reactive resin coatings to be installed from different manufacturers.

Most mineral levelling compounds cannot be coated directly with reactive resins. Although the surfaces appear smooth and hard, they are unsuitable for the absorption of reaction resins. In self-levelling compounds, fines, polymers and additives can accumulate on the surface, leading to reduced adhesion and subsequent damage to the coating when moisture penetrates from below. When installing such products, one runs a considerable risk of subsequent delamination of the coating.

Even more suitable levelling compounds must first be prepared to absorb subsequent coatings by adequate substrate preparation, e.g. by shot-blasting. A significantly more economical solution is offered by the newly developed, matching KLB levelling compounds, which have been specifically designed to be covered with reactive resin coatings.

Efficient solution from one provider: reduced installation times thanks to coatable KLB levelling compounds.

By carefully matching mineral levelling compounds to subsequent reactive resin coatings, an economical renovation concept for robust industrial floors can be achieved. The resilient levelling compounds from KLB Kötztal offer a solution from a single source with qualified coordination of the products used:

View the product


Fast-curing, self-levelling 3-component epoxy cement levelling layer (ECC), also suitable as a vapour-venting intermediate layer on substrates in contact with the soil.

View the product


Self-levelling, fast-curing, polymer-modified cement levelling compound for versatile use.

Both levelling compounds enable fast and uncomplicated installation in a recommended layer thickness of 3 – 10 mm. The fast and low-shrinkage curing provides a high-strength base for subsequent reactive resin coatings. In combination with such, floor coverings for commercial and industrial use can also be created with forklift suitability – and thus higher mechanical load-bearing capacity.

Both compounds are low-emission and therefore suitable for indoor areas and even lounges. EC 610 C is particularly advantageous as a vapour-compensating layer for coatings on concrete slabs in contact with the soil or green ones. The coating compounds are fast-curing, quickly coatable, low-shrinkage drying and at the same time, water-proof.

Properly combined: fast recoating after only 16 to 24 hours.

Depending on the levelling compound, KLB-SYSTEM EPOXID EP 724 E Haftgrund Super (for EC 610 C) or the low-emission dispersion base coat EC 940 Grund (for EC 633 C) can be used as primer on the mechanically prepared substrate. Alternatively, epoxy resin primers such as KLB-SYSTEM EPOXID EP 53 AgBB-Spezialgrund can be used when the surface is being sanded openly with quartz sand (grain size 0.7/1.2 mm).

The fast hardening ensures that a primer for the subsequent reactive resin coating can be applied after only 16 to 24 hours. KLB-SYSTEM EPOXID EP 724 E Haftgrund Super is suitable as system primer at a consumption of 0.2 – 0.3 kg/m². After a short curing time of approx. 12 – 16 hours, a recommended epoxy or polyurethane resin coating can be applied.

The products are matched to each other down to the last detail and can be combined optimally and in a time-saving manner without the need for an additional intermediate layer. The advantages of such a system solution are therefore obvious : the build-up is low-emission and can be installed in a wide variety of sectors.


Curing time (at 20 °C / 68 °F)12 – 16 hours 8 – 10 hours
Further coatings (at 20 °C / 68 °F) after15 – 24 hours15 – 24 hours
Compressive strength (after 28 days)55 N/mm²50 N/mm²
Flexural strength (after 28 days)11 N/mm²8 N/mm²
Processing temperature (room and floor)10 °C – 28 °C / 50 °F – 82.4 °F5 °C – 28 °C / 41 °F – 82.4 °F

Register now!

You are just a few clicks away from staying up to date with us.

Never miss out on new products or systems again and receive the latest references or important company information directly and at any time in your inbox.

KLB Newsletter Registrierung

More news in this category

PU 405 – new quality for better processing

PU 405 with its new quality has an optimised flow and working time that improves wet-on-wet processing at the same time, so that roller marks are no longer visible when designing l...

  • Innovation
Statically crack-bridging EP 5590 of 0.6 mm (- 10 °C) within the OS 8 system

EP 5590 is a flexibilised, water vapour-permable epoxy resin coating with a special static crack-bridging capability of 0.6 mm (at -10 °C).

  • Innovation
Bodenabdichtung in einer Gewerbeküche
Sealing walls and floors with CW 510 and CW 512

These new products are suitable for sealing floor surfaces in showers and sanitary facilities, as waterproofing on bathroom walls or for liquid-tight swimming pool surrounds and ha...

  • Innovation
Oberflächenschutzbeschichtung OS 8 Flex auf einer Einfahrt zu einer Tiefgarage
Flexibilised surface protection systems with static crack-bridging

Systems K6 and K7 are very robust, flexibilised surface protection systems tested based on OS 8 for mechanically highly loaded indoor surfaces. Due to their static crack-bridging c...

  • Innovation

The website is not optimised for use in your browser. This results in display errors and limited functionality. We recommend that you use one of the following free browsers for unrestricted use of our website.